The template for codec enable settings was taking a value as 1 if it was set in the settings. It was not taking the actual value inside it. So I have edited the templates to check the value if it's set to true.
I was having an issue where my T41P phones were getting provisioned with IPv4 & IPv6 - even though I specified in default settings yealink_ip_address_mode=0 for IPv4 only. Checked the y000000000036.cfg, which was setting it correctly. The issue was that {$mac}.cfg was overriding the correct setting. There were several instances of "network.ip_address_mode = 2" in this file, which specifies ipv4&ipv6. I changed all 5 of those entries in this file to pull from the default setting {$yealink_ip_address_mode} rather than just setting a static value of 2. I don't know why it has this listed in this file 5 times. But, this change resolved my issue and will force the T41P provisioning to follow FusionPBX default settings.
Added a line to set SRTP encryption. the default setting yealink_srtp_encryption was not setting properly to my T56a devices. I downloaded my config files and did not find an entry for srtp at all.
compared with the t54w template and it did have a srtp setting. So I pretty much stole the line from the T54w template and dumped it in here.
The T54w template is vastly superior to this one and this probably needs a rewrite to bring it in line.
Tested on my T56a and it at least gets the job done.
* Added two new minor hardware revisions, the CP925 and T42U, and added the voice.tone.country = {} to all templates, previously missing on most
* Minor typo from a wrong window issue, and removing the commented examples for easier grepping
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
* Update y000000000150.cfg
This should be paired with a default setting to match. it controls the behavior of the headset if you make a call while it is connected. by default (0), yealink phones will not connect the call via the headset. if you set it to 1, the phone will immediately start using the headset for the call, instead of requiring you to press the headset button after dialing.
* Grandstream HT802 Added Offhook Auto-dial variables
* Grandstream HT802 Added Offhook Auto-dial variables
* Grandstream GRP261x Make Configuration Keypad Lock configurable, fix default
* Grandstream Add grandstream_dhcp_time_zone across all templates
* Yealink Added yealink_missed_calllog to control whether missed calls are logged or not
* Grandstream HT802 update variable name to not use dash (which was breaking the template)
Krushali Shah
Mendel
Antonio Fernandez
levishores
zrd740
FusionPBX
garryavx
Alex
Harry Foster
Dan
Ben
Anthony