dbxe
/
fusionpbx
2
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
fusionpbx/resources/templates/provision/yealink/t28p/{$mac}.cfg

2138 lines
81 KiB
INI
Raw Blame History

This file contains invisible Unicode characters

This file contains invisible Unicode characters that are indistinguishable to humans but may be processed differently by a computer. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

#!version:1.0.0.1
##File header "#!version:1.0.0.1" can not be edited or deleted.##
#######################################################################################
## Account1 Settings ##
#######################################################################################
#Enable or disable the account 1; 0-Disabled (default), 1-Enabled;
{if isset($user_password_1) }
account.1.enable = 1
{else}
account.1.enable = 0
{/if}
#Configure the label displayed on the LCD screen for account 1.
account.1.label = {$display_name_1}
#Configure the display name of account 1.
account.1.display_name = {$display_name_1}
#Configure the username and password for register authentication.
account.1.auth_name = {$auth_id_1}
account.1.password = {$user_password_1}
#Configure the register user name.
account.1.user_name = {$user_id_1}
#Enable or disable the phone to receive the messages from the server only; 0-Disabled (default), 1-Enabled;
account.1.sip_trust_ctrl = 1
#Configure the SIP server address.
account.1.sip_server_host = {$server_address_1}
#Specify the port for the SIP server. The default value is 5060.
account.1.sip_server_port = {$sip_port_1}
#Enable or disable the use of the outbound proxy server; 0-Disabled (default), 1-Enabled;
#Specify the IP address or domain name of the outbound proxy server.
account.1.outbound_host = {$outbound_proxy_1}
#Specify the server port, the default value is 5060.
account.1.outbound_port =
#Configure the transport type; 0-UDP (default), 1-TCP, 2-TLS, 3-DNS SRV;
{if $sip_transport_1 == 'udp'}account.1.transport = 0{/if}
{if $sip_transport_1 == 'tcp'}account.1.transport = 1{/if}
{if $sip_transport_1 == 'tls'}account.1.transport = 2{/if}
{if $sip_transport_1 == 'dns srv'}account.1.transport = 3{/if}
account.1.outbound_proxy.1.address = {$outbound_proxy_primary_1}
account.1.outbound_proxy.2.address = {$outbound_proxy_secondary_1}
account.1.outbound_proxy_enable = {if isset($outbound_proxy_primary_1)}1{else}0{/if}
{if isset($outbound_proxy_1_port)}
account.1.outbound_proxy.1.port = {$outbound_proxy_1_port}
{else}
account.1.outbound_proxy.1.port = 5060
{/if}
{if isset($outbound_proxy_1_port)}
account.1.outbound_proxy.2.port = {$outbound_proxy_2_port}
{else}
account.1.outbound_proxy.2.port = 5060
{/if}
#Configure the address of the backup outbound proxy server.
account.1.backup_outbound_host =
#Specify the port of the backup outbound proxy server, the default value is 5060.
account.1.backup_outbound_port =
#Configure the voice mail number of account 1.
voice_mail.number.1 = {$voicemail_number}
#Configure the proxy server to account 1.
account.1.proxy_require =
#Enable or disable the use of the timer to periodically refresh the DNS-SRV query result; 0-Disabled (default), 1-Enabled;
#Require reboot;
account.1.srv_ttl_timer_enable =
#Configure the type of DNS-SRV query; 0-UDP, TCP and TLS (default), 1-UDP, 2-TCP, 3-TLS;
#Require reboot;
account.1.dns_srv_type =
#Enable or disable the anonymous call feature; 0-Disabled (default), 1-Enabled;
account.1.anonymous_call =
#Configure the on code and off code of the anonymous call feature.
account.1.anonymous_call_oncode =
account.1.anonymous_call_offcode =
#Enable or disable the reject anonymous call feature; 0-Disabled (default), 1-Enabled;
account.1.reject_anonymous_call =
#Configure the on code and off code of the reject anonymous call feature.
account.1.anonymous_reject_oncode =
account.1.anonymous_reject_offcode =
#Configure the SIP port for account 1, the default value is 5060.
account.1.sip_listen_port =
#Configure the register expiry time (in seconds), the default value is 3600.
account.1.expires = {$register_expires_1}
#Enable or disable the 100 reliable retransmission; 0-Disabled, 1-Enabled (default);
account.1.100rel_enable = {$yealink_retransmission}
#Enable or disable the resource reservation; 0-Disabled (default), 1-Enabled;
account.1.precondition =
#Enable or disable the phone to subscribe the register status; 0-Disabled (default), 1-Enabled;
account.1.subscribe_register =
#Enable or disable the phone to subscribe the message waiting indicator; 0-Disabled (default), 1-Enabled;
account.1.subscribe_mwi =
#Configure MWI subscribe expiry time (in seconds). It ranges from 0 to 84600, the default value is 3600.
account.1.subscribe_mwi_expires =
#Configure the type of SIP header(s) to carry the caller ID; 0-FROM (default), 1-PAI 2-PAI-FROM, 3-PRID-PAI-FROM, 4-PAI-RPID-FROM, 5-RPID-FROM;
account.1.cid_source = {$yealink_cid_source}
#Configure the presentation of the callee ID; 0-PAI-PRID, 1-DIALED DIGITS (default), 2-RFC4916;
account.1.cp_source = 2
#Enable or disable the session timer; 0-Disabled (default), 1-Enabled;
account.1.session_timer.enable = {$yealink_session_timer}
#Configure the refresh session timer interval (in seconds). It ranges from 1 to 9999.
account.1.session_timer.expires =
#Configure the session timer refresher; 0-Uac (default), 1-Uas;
account.1.session_timer.refresher =
#Enable or disable the "user=phone"; 0-Disabled (default), 1-Enabled;
account.1.enable_user_equal_phone =
#Specify whether to encrypt the SIP messages; 0-Disabled, 1-Forced, 2-Negotiated;
account.1.srtp_encryption = {$yealink_srtp_encryption}
#Configure the RTP packet time. The valid values are 0 (Disabled), 10, 20 (default), 30, 40, 50, 60.
account.1.ptime =
#Assign account 1 as shared line; 0-Disabled (default), 1-BSFT shared line, 2-Draft bridge line appearance;
{if isset($shared_line_1) }
account.1.shared_line = {$shared_line_1}
{else}
account.1.shared_line = 0
{/if}
#Configure BLA number for account 1 and the subscribe period (in seconds). It ranges from 60 to 7200, the default value is 300.
account.1.bla_number =
account.1.bla_subscribe_period =
#Enable or disable call pickup using dialog-info SIP header; 0-Disabled (default), 1-Enabled;
account.1.dialoginfo_callpickup =
#Configure the directed and group pickup codes for account 1, the settings on a per-account basis take precedence over the settings on the phone.
account.1.group_pickup_code =
account.1.direct_pickup_code =
#Enable or disable the auto answer feature; 0-Disabled (default), 1-Enabled;
account.1.auto_answer =
#Enable or disable the phone to record the missed call; 0-Disabled, 1-Enabled (default);
account.1.missed_calllog =
#Enable or disable the phone to subscribe to the voicemail through the message waiting indicator; 0-Disabled (default), 1-Enabled;
account.1.subscribe_mwi_to_vm =
#Enable or disable the phone to send the MAC address and line number in the Register message; 0-Disabled (default), 1-Enabled;
account.1.register_mac =
#Enable or disable the phone to send the line number in the Register message; 0-Disabled, 1-Enabled (default);
account.1.register_line =
#Configure the interval (in seconds) the phone retries to register when account 1 fails to register. It ranges from 0 to 1800, the default value is 30.
account.1.reg_fail_retry_interval =
#Configure the conference type; 0-Local (default), 2-Network Conference;
account.1.conf_type =
#Configure the conference URI (a SIP URI, or use part of the SIP URI). For example, "conference@domain.com" or "conference".
account.1.conf_uri =
#Configure the BLF list URI (a SIP URI, or use part of the SIP URI). For example, "2300_blflist@domain.com" or "2300_blflist".
account.1.blf.blf_list_uri =
#Configure the pickup code of BLF List.
account.1.blf_list_code =
#Configure the bargein code.
account.1.blf_list_barge_in_code =
#Configure the BLF subscribe period (in seconds), the default value is 1800.
account.1.blf.subscribe_period =
#Configure the ACD subscribe period (in seconds). It ranges from 120 to 3600 (default).
account.1.subscribe_acd_expires =
#Configure the SIP server type; 0-Default (default), 2-BroadSoft, 4-Cosmocom;
account.1.sip_server_type =
#Enable or disable the phone to use the customized theme; 0-Disabled (default), 1-Enabled;
account.1.idle_screen_enable =
#Define the access URL of the customized theme.
account.1.idle_screen_url =
#Enable or disable the SIP signal encode; 0-Disabled (default), 1-Enabled (RC 4);
account.1.enable_signal_encode =
#Configure the key for encoding.
account.1.signal_encode_key =
#Configure the DTMF type; 0-INBAND, 1-RFC2833 (default), 2-SIP INFO, 3-AUTO+SIP INFO;
account.1.dtmf.type =
#Configure the RFC2833 payload. It ranges from 96 to 225, the default value is 101.
account.1.dtmf.dtmf_payload =
#Configure the DTMF info type when using the SIP INFO; 0-Disabled (default), 1-DTMF-Relay, 2-DTMF, 3-Telephone-Event;
account.1.dtmf.info_type =
#Enable or disable the phone to support the simplified SIP header; 0-Disabled (default), 1-Enabled;
account.1.compact_header_enable =
#########################################################################
## NAT Settings ##
#########################################################################
#Enable or disable the NAT traversal; 0-Disabled (default), 1-STUN;
account.1.nat.nat_traversal = {if isset($stun_server)}1{else}0{/if}
#Configure the STUN server address.
account.1.nat.stun_server = {$stun_server}
#Configure the STUN server port, the default value is 3478.
account.1.nat.stun_port = {if isset($stun_port)}{$stun_port}{else}3478{/if}
#Enable or disable the NAT keep-alive; 0-Disabled, 1-Default (default), 2-Option, 3-Notify;
account.1.nat.udp_update_enable = 3
#Specify the keep-alive interval (in seconds), the default value is 30.
account.1.nat.udp_update_time =
#Enable or disable the NAT Rport; 0-Disabled (default), 1-Enabled;
account.1.nat.rport = {$yealink_rport}
#Configure the session timer (in seconds), the default values of T1, T2, T3 are 0.5, 4, 5.
account.1.advanced.timer_t1 =
account.1.advanced.timer_t2 =
account.1.advanced.timer_t4 =
#Assign a ringtone for account 1. The system ring tones are: common.wav (default), Ring1.wav, Ring2.wav,¡­¡­Ring8.wav.
#If you configure the custom ring tone (Family.wav) for the account, the value format is: Family.wav
#If you configure the system ring tone (Ring2.wav) for the account, the value format is: Ring2.wav
account.1.ringtone.ring_type =
#Enable or disable the phone to display the picture when receiving the specified SIP message; 0-Disabled, 1-Enabled (default);
account.1.picture_info_enable =
#Audio codecs for account 1 (Y ranges from 1 to 13).
#account.1.codec.y.enable =
#account.1.codec.y.payload_type =
#account.1.codec.y.priority =
#account.1.codec.y.rtpmap =
account.1.codec.1.enable = 1
account.1.codec.1.payload_type = PCMU
account.1.codec.1.priority = 1
account.1.codec.1.rtpmap = 0
account.1.codec.2.enable = 1
account.1.codec.2.payload_type = PCMA
account.1.codec.2.priority = 2
account.1.codec.2.rtpmap = 8
account.1.codec.3.enable = 0
account.1.codec.3.payload_type = G723_53
account.1.codec.3.priority =4
account.1.codec.3.rtpmap = 4
account.1.codec.4.enable = 0
account.1.codec.4.payload_type = G723_63
account.1.codec.4.priority = 0
account.1.codec.4.rtpmap = 4
account.1.codec.5.enable = 1
account.1.codec.5.payload_type = G729
account.1.codec.5.priority = 3
account.1.codec.5.rtpmap = 18
account.1.codec.6.enable = 1
account.1.codec.6.payload_type = G722
account.1.codec.6.priority = 4
account.1.codec.6.rtpmap = 9
account.1.codec.7.enable =
account.1.codec.7.payload_type =
account.1.codec.7.priority =
account.1.codec.7.rtpmap =
account.1.codec.8.enable = 0
account.1.codec.8.payload_type = G726-16
account.1.codec.8.priority = 0
account.1.codec.8.rtpmap = 112
account.1.codec.9.enable = 0
account.1.codec.9.payload_type = G726-24
account.1.codec.9.priority = 0
account.1.codec.9.rtpmap = 102
account.1.codec.10.enable = 0
account.1.codec.10.payload_type = G726-32
account.1.codec.10.priority = 0
account.1.codec.10.rtpmap = 2
account.1.codec.11.enable = 0
account.1.codec.11.payload_type = G726-40
account.1.codec.11.priority = 0
account.1.codec.11.rtpmap = 104
account.1.codec.12.enable = 0
account.1.codec.12.payload_type = iLBC_13_3
account.1.codec.12.priority = 0
account.1.codec.12.rtpmap = 97
account.1.codec.13.enable = 0
account.1.codec.13.payload_type = iLBC_15_2
account.1.codec.13.priority = 0
account.1.codec.13.rtpmap = 97
#######################################################################################
## Account2 Settings ##
#######################################################################################
#Enable or disable the account 2; 0-Disabled (default), 1-Enabled;
{if isset($user_password_2) }
account.2.enable = 1
{else}
account.2.enable = 0
{/if}
#Configure the label displayed on the LCD screen for account 2.
account.2.label = {$display_name_2}
#Configure the display name of account 2.
account.2.display_name = {$display_name_2}
#Configure the username and password for register authentication.
account.2.auth_name = {$auth_id_2}
account.2.password = {$user_password_2}
#Configure the register user name.
account.2.user_name = {$user_id_2}
#Enable or disable the phone to receive the messages from the server only; 0-Disabled (default), 1-Enabled;
account.2.sip_trust_ctrl = 1
#Configure the SIP server address.
account.2.sip_server_host = {$server_address_2}
#Specify the port for the SIP server. The default value is 5060.
account.2.sip_server_port = {$sip_port_2}
#Enable or disable the use of the outbound proxy server; 0-Disabled (default), 1-Enabled;
#Specify the IP address or domain name of the outbound proxy server.
account.2.outbound_host = {$outbound_proxy_2}
#Specify the server port, the default value is 5060.
account.2.outbound_port =
#Configure the transport type; 0-UDP (default), 1-TCP, 2-TLS, 3-DNS SRV;
{if $sip_transport_2 == 'udp'}account.2.transport = 0{/if}
{if $sip_transport_2 == 'tcp'}account.2.transport = 1{/if}
{if $sip_transport_2 == 'tls'}account.2.transport = 2{/if}
{if $sip_transport_2 == 'dns srv'}account.2.transport = 3{/if}
account.2.outbound_proxy.1.address = {$outbound_proxy_primary_2}
account.2.outbound_proxy.2.address = {$outbound_proxy_secondary_2}
account.2.outbound_proxy_enable = {if isset($outbound_proxy_primary_2)}1{else}0{/if}
#Configure the address of the backup outbound proxy server.
account.2.backup_outbound_host =
#Specify the port of the backup outbound proxy server, the default value is 5060.
account.2.backup_outbound_port =
#Configure the voice mail number of account 2.
voice_mail.number.2 = *97
#Configure the proxy server to account 2.
account.2.proxy_require =
#Enable or disable the use of the timer to periodically refresh the DNS-SRV query result; 0-Disabled (default), 1-Enabled;
#Require reboot;
account.2.srv_ttl_timer_enable =
#Configure the type of DNS-SRV query; 0-UDP, TCP and TLS (default), 1-UDP, 2-TCP, 3-TLS;
#Require reboot;
account.2.dns_srv_type =
#Enable or disable the anonymous call feature; 0-Disabled (default), 1-Enabled;
account.2.anonymous_call =
#Configure the on code and off code of the anonymous call feature.
account.2.anonymous_call_oncode =
account.2.anonymous_call_offcode =
#Enable or disable the reject anonymous call feature; 0-Disabled (default), 1-Enabled;
account.2.reject_anonymous_call =
#Configure the on code and off code of the reject anonymous call feature.
account.2.anonymous_reject_oncode =
account.2.anonymous_reject_offcode =
#Configure the SIP port for account 2, the default value is 5060.
account.2.sip_listen_port =
#Configure the register expiry time (in seconds), the default value is 3600.
account.2.expires = {$register_expires_2}
#Enable or disable the 100 reliable retransmission; 0-Disabled (default), 1-Enabled;
account.2.100rel_enable = {$yealink_retransmission}
#Enable or disable the resource reservation; 0-Disabled (default), 1-Enabled;
account.2.precondition =
#Enable or disable the phone to subscribe the register status; 0-Disabled (default), 1-Enabled;
account.2.subscribe_register =
#Enable or disable the phone to subscribe the message waiting indicator; 0-Disabled (default), 1-Enabled;
account.2.subscribe_mwi =
#Configure MWI subscribe expiry time (in seconds). It ranges from 0 to 84600, the default value is 3600.
account.2.subscribe_mwi_expires =
#Configure the type of SIP header(s) to carry the caller ID; 0-FROM (default), 1-PAI 2-PAI-FROM, 3-PRID-PAI-FROM, 4-PAI-RPID-FROM, 5-RPID-FROM;
account.2.cid_source = {$yealink_cid_source}
#Configure the presentation of the callee ID; 0-PAI-PRID, 1-DIALED DIGITS (default), 2-RFC4916;
account.2.cp_source = 2
#Enable or disable the session timer; 0-Disabled (default), 1-Enabled;
account.2.session_timer.enable = {$yealink_session_timer}
#Configure the refresh session timer interval (in seconds). It ranges from 1 to 9999.
account.2.session_timer.expires =
#Configure the session timer refresher; 0-Uac (default), 1-Uas;
account.2.session_timer.refresher =
#Enable or disable the "user=phone"; 0-Disabled (default), 1-Enabled;
account.2.enable_user_equal_phone =
#Specify whether to encrypt the SIP messages; 0-Disabled, 1-Forced, 2-Negotiated;
account.2.srtp_encryption =
#Configure the RTP packet time. The valid values are 0 (Disabled), 10, 20 (default), 30, 40, 50, 60.
account.2.ptime =
#Assign account 2 as shared line; 0-Disabled (default), 1-BSFT shared line, 2-Draft bridge line appearance;
{if isset($shared_line_2) }
account.2.shared_line = {$shared_line_2}
{else}
account.2.shared_line = 0
{/if}
#Configure BLA number for account 2 and the subscribe period (in seconds). It ranges from 60 to 7200, the default value is 300.
account.2.bla_number =
account.2.bla_subscribe_period =
#Enable or disable call pickup using dialog-info SIP header; 0-Disabled (default), 1-Enabled;
account.2.dialoginfo_callpickup =
#Configure the directed and group pickup codes for account 2, the settings on a per-account basis take precedence over the settings on the phone.
account.2.group_pickup_code =
account.2.direct_pickup_code =
#Enable or disable the auto answer feature; 0-Disabled (default), 1-Enabled;
account.2.auto_answer =
#Enable or disable the phone to record the missed call; 0-Disabled, 1-Enabled (default);
account.2.missed_calllog =
#Enable or disable the phone to subscribe to the voicemail through the message waiting indicator; 0-Disabled (default), 1-Enabled;
account.2.subscribe_mwi_to_vm =
#Enable or disable the phone to send the MAC address in the Register message; 0-Disabled (default), 1-Enabled;
account.2.register_mac =
#Enable or disable the phone to send the line number in the Register message; 0-Disabled, 1-Enabled (default);
account.2.register_line =
#Configure the interval (in seconds) the phone retries to register when account 2 fails to register. It ranges from 0 to 1800, the default value is 30.
account.2.reg_fail_retry_interval =
#Configure the conference type; 0-Local (default), 2-Network Conference;
account.2.conf_type =
#Configure the conference URI (a SIP URI, or use part of the SIP URI). For example, "conference@domain.com" or "conference".
account.2.conf_uri =
#Configure the BLF list URI (a SIP URI, or use part of the SIP URI). For example, "2300_blflist@domain.com" or "2300_blflist".
account.2.blf.blf_list_uri =
#Configure the pickup code of BLF List.
account.2.blf_list_code =
#Configure the bargein code.
account.2.blf_list_barge_in_code =
#Configure the BLF subscribe period (in seconds), the default value is 1800.
account.2.blf.subscribe_period =
#Configure the ACD subscribe period (in seconds). It ranges from 120 to 3600 (default).
account.2.subscribe_acd_expires =
#Configure the SIP server type; 0-Default (default), 2-BroadSoft, 4-Cosmocom;
account.2.sip_server_type =
#Enable or disable the phone to use the customized theme; 0-Disabled (default), 1-Enabled;
account.2.idle_screen_enable =
#Define the access URL of the customized theme.
account.2.idle_screen_url =
#Enable or disable the SIP signal encode; 0-Disabled (default), 1-Enabled (RC 4);
account.2.enable_signal_encode =
#Configure the key for encoding.
account.2.signal_encode_key =
#Configure the DTMF type; 0-INBAND, 1-RFC2833 (default), 2-SIP INFO, 3-AUTO+SIP INFO;
account.2.dtmf.type =
#Configure the RFC2833 payload. It ranges from 96 to 225, the default value is 101.
account.2.dtmf.dtmf_payload =
#Configure the DTMF info type when using the SIP INFO; 0-Disabled (default), 1-DTMF-Relay, 2-DTMF, 3-Telephone-Event;
account.2.dtmf.info_type =
#Enable or disable the phone to support the simplified SIP header; 0-Disabled (default), 1-Enabled;
account.2.compact_header_enable =
#########################################################################
## NAT Settings ##
#########################################################################
#Enable or disable the NAT traversal; 0-Disabled (default), 1-STUN;
account.2.nat.nat_traversal = {if isset($stun_server)}1{else}0{/if}
#Configure the STUN server address.
account.2.nat.stun_server = {$stun_server}
#Configure the STUN server port, the default value is 3478.
account.2.nat.stun_port = {if isset($stun_port)}{$stun_port}{else}3478{/if}
#Enable or disable the NAT keep-alive; 0-Disabled, 1-Enabled (default);
account.2.nat.udp_update_enable =
#Specify the keep-alive interval (in seconds), the default value is 30.
account.2.nat.udp_update_time =
#Enable or disable the NAT Rport; 0-Disabled (default), 1-Enabled;
account.2.nat.rport = {$yealink_rport}
#Configure the session timer (in seconds), the default values of T1, T2, T3 are 0.5, 4, 5.
account.2.advanced.timer_t1 =
account.2.advanced.timer_t2 =
account.2.advanced.timer_t4 =
#Assign a ringtone for account 2. The system ring tones are: common.wav (default), Ring1.wav, Ring2.wav,¡­¡­Ring8.wav.
#If you configure the custom ring tone (Family.wav) for the account, the value format is: Family.wav
#If you configure the system ring tone (Ring2.wav) for the account, the value format is: Ring2.wav
account.2.ringtone.ring_type =
#Enable or disable the phone to display the picture when receiving the specified SIP message; 0-Disabled, 1-Enabled (default);
account.2.picture_info_enable =
#Audio codecs for account 2 (Y ranges from 1 to 13).
#account.2.codec.Y.enable =
#account.2.codec.Y.payload_type =
#account.2.codec.Y.priority =
#account.2.codec.Y.rtpmap =
account.2.codec.1.enable = 1
account.2.codec.1.payload_type = PCMU
account.2.codec.1.priority = 1
account.2.codec.1.rtpmap = 0
account.2.codec.2.enable = 1
account.2.codec.2.payload_type = PCMA
account.2.codec.2.priority = 2
account.2.codec.2.rtpmap = 8
account.2.codec.3.enable = 0
account.2.codec.3.payload_type = G723_53
account.2.codec.3.priority =4
account.2.codec.3.rtpmap = 4
account.2.codec.4.enable = 0
account.2.codec.4.payload_type = G723_63
account.2.codec.4.priority = 0
account.2.codec.4.rtpmap = 4
account.2.codec.5.enable = 1
account.2.codec.5.payload_type = G729
account.2.codec.5.priority = 3
account.2.codec.5.rtpmap = 18
account.2.codec.6.enable = 1
account.2.codec.6.payload_type = G722
account.2.codec.6.priority = 4
account.2.codec.6.rtpmap = 9
account.2.codec.7.enable =
account.2.codec.7.payload_type =
account.2.codec.7.priority =
account.2.codec.7.rtpmap =
account.2.codec.8.enable = 0
account.2.codec.8.payload_type = G726-16
account.2.codec.8.priority = 0
account.2.codec.8.rtpmap = 112
account.2.codec.9.enable = 0
account.2.codec.9.payload_type = G726-24
account.2.codec.9.priority = 0
account.2.codec.9.rtpmap = 102
account.2.codec.10.enable = 0
account.2.codec.10.payload_type = G726-32
account.2.codec.10.priority = 0
account.2.codec.10.rtpmap = 2
account.2.codec.11.enable = 0
account.2.codec.11.payload_type = G726-40
account.2.codec.11.priority = 0
account.2.codec.11.rtpmap = 104
account.2.codec.12.enable = 0
account.2.codec.12.payload_type = iLBC_13_3
account.2.codec.12.priority = 0
account.2.codec.12.rtpmap = 97
account.2.codec.13.enable = 0
account.2.codec.13.payload_type = iLBC_15_2
account.2.codec.13.priority = 0
account.2.codec.13.rtpmap = 97
#######################################################################################
## Account3 Settings ##
#######################################################################################
#Enable or disable the account 3; 0-Disabled (default), 1-Enabled;
{if isset($user_password_3) }
account.3.enable = 1
{else}
account.3.enable = 0
{/if}
#Configure the label displayed on the LCD screen for account 3.
account.3.label = {$display_name_3}
#Configure the display name of account 3.
account.3.display_name = {$display_name_3}
#Configure the username and password for register authentication.
account.3.auth_name = {$auth_id_3}
account.3.password = {$user_password_3}
#Configure the register user name.
account.3.user_name = {$user_id_3}
#Enable or disable the phone to receive the messages from the server only; 0-Disabled (default), 1-Enabled;
account.3.sip_trust_ctrl = 1
#Configure the SIP server address.
account.3.sip_server_host = {$server_address_3}
#Specify the port for the SIP server. The default value is 5060.
account.3.sip_server_port = {$sip_port_3}
#Enable or disable the use of the outbound proxy server; 0-Disabled (default), 1-Enabled;
#Specify the IP address or domain name of the outbound proxy server.
account.3.outbound_host = {$outbound_proxy_3}
#Specify the server port, the default value is 5060.
account.3.outbound_port =
#Configure the transport type; 0-UDP (default), 1-TCP, 2-TLS, 3-DNS SRV;
{if $sip_transport_3 == 'udp'}account.3.transport = 0{/if}
{if $sip_transport_3 == 'tcp'}account.3.transport = 1{/if}
{if $sip_transport_3 == 'tls'}account.3.transport = 2{/if}
{if $sip_transport_3 == 'dns srv'}account.3.transport = 3{/if}
account.3.outbound_proxy.1.address = {$outbound_proxy_primary_3}
account.3.outbound_proxy.2.address = {$outbound_proxy_secondary_3}
account.3.outbound_proxy_enable = {if isset($outbound_proxy_primary_3)}1{else}0{/if}
#Configure the address of the backup outbound proxy server.
account.3.backup_outbound_host =
#Specify the port of the backup outbound proxy server, the default value is 5060.
account.3.backup_outbound_port =
#Configure the voice mail number of account 3.
voice_mail.number.3 =
#Configure the proxy server to account 3.
account.3.proxy_require =
#Enable or disable the use of the timer to periodically refresh the DNS-SRV query result; 0-Disabled (default), 1-Enabled;
#Require reboot;
account.3.srv_ttl_timer_enable =
#Configure the type of DNS-SRV query; 0-UDP, TCP and TLS (default), 1-UDP, 2-TCP, 3-TLS;
#Require reboot;
account.3.dns_srv_type =
#Enable or disable the anonymous call feature; 0-Disabled (default), 1-Enabled;
account.3.anonymous_call =
#Configure the on code and off code of the anonymous call feature.
account.3.anonymous_call_oncode =
account.3.anonymous_call_offcode =
#Enable or disable the reject anonymous call feature; 0-Disabled (default), 1-Enabled;
account.3.reject_anonymous_call =
#Configure the on code and off code of the reject anonymous call feature.
account.3.anonymous_reject_oncode =
account.3.anonymous_reject_offcode =
#Configure the SIP port for account 3, the default value is 5060.
account.3.sip_listen_port =
#Configure the register expiry time (in seconds), the default value is 3600.
account.3.expires = {$register_expires_3}
#Enable or disable the 100 reliable retransmission; 0-Disabled (default), 1-Enabled;
account.3.100rel_enable = {$yealink_retransmission}
#Enable or disable the resource reservation; 0-Disabled (default), 1-Enabled;
account.3.precondition =
#Enable or disable the phone to subscribe the register status; 0-Disabled (default), 1-Enabled;
account.3.subscribe_register =
#Enable or disable the phone to subscribe the message waiting indicator; 0-Disabled (default), 1-Enabled;
account.3.subscribe_mwi =
#Configure MWI subscribe expiry time (in seconds). It ranges from 0 to 84600, the default value is 3600.
account.3.subscribe_mwi_expires =
#Configure the type of SIP header(s) to carry the caller ID; 0-FROM (default), 1-PAI 2-PAI-FROM, 3-PRID-PAI-FROM, 4-PAI-RPID-FROM, 5-RPID-FROM;
account.3.cid_source = {$yealink_cid_source}
#Configure the presentation of the callee ID; 0-PAI-PRID, 1-DIALED DIGITS (default), 2-RFC4916;
account.3.cp_source = 2
#Enable or disable the session timer; 0-Disabled (default), 1-Enabled;
account.3.session_timer.enable = {$yealink_session_timer}
#Configure the refresh session timer interval (in seconds). It ranges from 1 to 9999.
account.3.session_timer.expires =
#Configure the session timer refresher; 0-Uac (default), 1-Uas;
account.3.session_timer.refresher =
#Enable or disable the "user=phone"; 0-Disabled (default), 1-Enabled;
account.3.enable_user_equal_phone =
#Specify whether to encrypt the SIP messages; 0-Disabled, 1-Forced, 2-Negotiated;
account.3.srtp_encryption =
#Configure the RTP packet time. The valid values are 0 (Disabled), 10, 20 (default), 30, 40, 50, 60.
account.3.ptime =
#Assign account 3 as shared line; 0-Disabled (default), 1-BSFT shared line, 2-Draft bridge line appearance;
{if isset($shared_line_3) }
account.3.shared_line = {$shared_line_3}
{else}
account.3.shared_line = 0
{/if}
#Configure BLA number for account 3 and the subscribe period (in seconds). It ranges from 60 to 7200, the default value is 300.
account.3.bla_number =
account.3.bla_subscribe_period =
#Enable or disable call pickup using dialog-info SIP header; 0-Disabled (default), 1-Enabled;
account.3.dialoginfo_callpickup =
#Configure the directed and group pickup codes for account 3, the settings on a per-account basis take precedence over the settings on the phone.
account.3.group_pickup_code =
account.3.direct_pickup_code =
#Enable or disable the auto answer feature; 0-Disabled (default), 1-Enabled;
account.3.auto_answer =
#Enable or disable the phone to record the missed call; 0-Disabled, 1-Enabled (default);
account.3.missed_calllog =
#Enable or disable the phone to subscribe to the voicemail through the message waiting indicator; 0-Disabled (default), 1-Enabled;
account.3.subscribe_mwi_to_vm =
#Enable or disable the phone to send the MAC address in the Register message; 0-Disabled (default), 1-Enabled;
account.3.register_mac =
#Enable or disable the phone to send theline number in the Register message; 0-Disabled, 1-Enabled (default);
account.3.register_line =
#Configure the interval (in seconds) the phone retries to register when account 3 fails to register. It ranges from 0 to 1800, the default value is 30.
account.3.reg_fail_retry_interval =
#Configure the conference type; 0-Local (default), 2-Network Conference;
account.3.conf_type =
#Configure the conference URI (a SIP URI, or use part of the SIP URI). For example, "conference@domain.com" or "conference".
account.3.conf_uri =
#Configure the BLF list URI (a SIP URI, or use part of the SIP URI). For example, "2300_blflist@domain.com" or "2300_blflist".
account.3.blf.blf_list_uri =
#Configure the pickup code of BLF List.
account.3.blf_list_code =
#Configure the bargein code.
account.3.blf_list_barge_in_code =
#Configure the BLF subscribe period (in seconds), the default value is 1800.
account.3.blf.subscribe_period =
#Configure the ACD subscribe period (in seconds). It ranges from 120 to 3600 (default).
account.3.subscribe_acd_expires =
#Configure the SIP server type; 0-Default (default), 2-BroadSoft, 4-Cosmocom;
account.3.sip_server_type =
#Enable or disable the phone to use the customized theme; 0-Disabled (default), 1-Enabled;
account.3.idle_screen_enable =
#Define the access URL of the customized theme.
account.3.idle_screen_url =
#Enable or disable the SIP signal encode; 0-Disabled (default), 1-Enabled (RC 4);
account.3.enable_signal_encode =
#Configure the key for encoding.
account.3.signal_encode_key =
#Configure the DTMF type; 0-INBAND, 1-RFC2833 (default), 2-SIP INFO, 3-AUTO+SIP INFO;
account.3.dtmf.type =
#Configure the RFC2833 payload. It ranges from 96 to 225, the default value is 101.
account.3.dtmf.dtmf_payload =
#Configure the DTMF info type when using the SIP INFO; 0-Disabled (default), 1-DTMF-Relay, 2-DTMF, 3-Telephone-Event;
account.3.dtmf.info_type =
#Enable or disable the phone to support the simplified SIP header; 0-Disabled (default), 1-Enabled;
account.3.compact_header_enable =
#########################################################################
## NAT Settings ##
#########################################################################
#Enable or disable the NAT traversal; 0-Disabled (default), 1-STUN;
account.3.nat.nat_traversal = {if isset($stun_server)}1{else}0{/if}
#Configure the STUN server address.
account.3.nat.stun_server = {$stun_server}
#Configure the STUN server port, the default value is 3478.
account.3.nat.stun_port = {if isset($stun_port)}{$stun_port}{else}3478{/if}
#Enable or disable the NAT keep-alive; 0-Disabled, 1-Enabled (default);
account.3.nat.udp_update_enable =
#Specify the keep-alive interval (in seconds), the default value is 30.
account.3.nat.udp_update_time =
#Enable or disable the NAT Rport; 0-Disabled (default), 1-Enabled;
account.3.nat.rport = {$yealink_rport}
#Configure the session timer (in seconds), the default values of T1, T2, T3 are 0.5, 4, 5.
account.3.advanced.timer_t1 =
account.3.advanced.timer_t2 =
account.3.advanced.timer_t4 =
#Assign a ringtone for account 3. The system ring tones are: common.wav (default), Ring1.wav, Ring2.wav,¡­¡­Ring8.wav.
#If you configure the custom ring tone (Family.wav) for the account, the value format is: Family.wav
#If you configure the system ring tone (Ring2.wav) for the account, the value format is: Ring2.wav
account.3.ringtone.ring_type =
#Enable or disable the phone to display the picture when receiving the specified SIP message; 0-Disabled, 1-Enabled (default);
account.3.picture_info_enable =
#Audio codecs for account 3 (Y ranges from 1 to 13).
#account.3.codec.Y.enable =
#account.3.codec.Y.payload_type =
#account.3.codec.Y.priority =
#account.3.codec.Y.rtpmap =
account.3.codec.1.enable = 1
account.3.codec.1.payload_type = PCMU
account.3.codec.1.priority = 1
account.3.codec.1.rtpmap = 0
account.3.codec.2.enable = 1
account.3.codec.2.payload_type = PCMA
account.3.codec.2.priority = 2
account.3.codec.2.rtpmap = 8
account.3.codec.3.enable = 0
account.3.codec.3.payload_type = G723_53
account.3.codec.3.priority =4
account.3.codec.3.rtpmap = 4
account.3.codec.4.enable = 0
account.3.codec.4.payload_type = G723_63
account.3.codec.4.priority = 0
account.3.codec.4.rtpmap = 4
account.3.codec.5.enable = 1
account.3.codec.5.payload_type = G729
account.3.codec.5.priority = 3
account.3.codec.5.rtpmap = 18
account.3.codec.6.enable = 1
account.3.codec.6.payload_type = G722
account.3.codec.6.priority = 4
account.3.codec.6.rtpmap = 9
account.3.codec.7.enable =
account.3.codec.7.payload_type =
account.3.codec.7.priority =
account.3.codec.7.rtpmap =
account.3.codec.8.enable = 0
account.3.codec.8.payload_type = G726-16
account.3.codec.8.priority = 0
account.3.codec.8.rtpmap = 112
account.3.codec.9.enable = 0
account.3.codec.9.payload_type = G726-24
account.3.codec.9.priority = 0
account.3.codec.9.rtpmap = 102
account.3.codec.10.enable = 0
account.3.codec.10.payload_type = G726-32
account.3.codec.10.priority = 0
account.3.codec.10.rtpmap = 2
account.3.codec.11.enable = 0
account.3.codec.11.payload_type = G726-40
account.3.codec.11.priority = 0
account.3.codec.11.rtpmap = 104
account.3.codec.12.enable = 0
account.3.codec.12.payload_type = iLBC_13_3
account.3.codec.12.priority = 0
account.3.codec.12.rtpmap = 97
account.3.codec.13.enable = 0
account.3.codec.13.payload_type = iLBC_15_2
account.3.codec.13.priority = 0
account.3.codec.13.rtpmap = 97
#######################################################################################
## Account4 Settings (For T38G only) ##
#######################################################################################
#Enable or disable the account 4; 0-Disabled (default), 1-Enabled;
{if isset($user_password_4) }
account.4.enable = 1
{else}
account.4.enable = 0
{/if}
#Configure the label displayed on the LCD screen for account 4.
account.4.label = {$display_name_4}
#Configure the display name of account 4.
account.4.display_name = {$display_name_4}
#Configure the username and password for register authentication.
account.4.auth_name = {$auth_id_4}
account.4.password = {$user_password_4}
#Configure the register user name.
account.4.user_name = {$user_id_4}
#Enable or disable the phone to receive the messages from the server only; 0-Disabled (default), 1-Enabled;
account.4.sip_trust_ctrl = 1
#Configure the SIP server address.
account.4.sip_server_host = {$server_address_4}
#Specify the port for the SIP server. The default value is 5060.
account.4.sip_server_port = {$sip_port_4}
#Enable or disable the use of the outbound proxy server; 0-Disabled (default), 1-Enabled;
#Specify the IP address or domain name of the outbound proxy server.
account.4.outbound_host = {$outbound_proxy_4}
#Specify the server port, the default value is 5060.
account.4.outbound_port =
#Configure the transport type; 0-UDP (default), 1-TCP, 2-TLS, 3-DNS SRV;
{if $sip_transport_4 == 'udp'}account.4.transport = 0{/if}
{if $sip_transport_4 == 'tcp'}account.4.transport = 1{/if}
{if $sip_transport_4 == 'tls'}account.4.transport = 2{/if}
{if $sip_transport_4 == 'dns srv'}account.4.transport = 3{/if}
account.4.outbound_proxy.1.address = {$outbound_proxy_primary_4}
account.4.outbound_proxy.2.address = {$outbound_proxy_secondary_4}
account.4.outbound_proxy_enable = {if isset($outbound_proxy_primary_4)}1{else}0{/if}
#Configure the address of the backup outbound proxy server.
account.4.backup_outbound_host =
#Specify the port of the backup outbound proxy server, the default value is 5060.
account.4.backup_outbound_port =
#Configure the voice mail number of account 4.
voice_mail.number.4 =
#Configure the proxy server to account 4.
account.4.proxy_require =
#Enable or disable the use of the timer to periodically refresh the DNS-SRV query result; 0-Disabled (default), 1-Enabled;
#Require reboot;
account.4.srv_ttl_timer_enable =
#Configure the type of DNS-SRV query; 0-UDP, TCP and TLS (default), 1-UDP, 2-TCP, 3-TLS;
#Require reboot;
account.4.dns_srv_type =
#Enable or disable the anonymous call feature; 0-Disabled (default), 1-Enabled;
account.4.anonymous_call =
#Configure the on code and off code of the anonymous call feature.
account.4.anonymous_call_oncode =
account.4.anonymous_call_offcode =
#Enable or disable the reject anonymous call feature; 0-Disabled (default), 1-Enabled;
account.4.reject_anonymous_call =
#Configure the on code and off code of the reject anonymous call feature.
account.4.anonymous_reject_oncode =
account.4.anonymous_reject_offcode =
#Configure the SIP port for account 4, the default value is 5060.
account.4.sip_listen_port =
#Configure the register expiry time (in seconds), the default value is 3600.
account.4.expires = {$register_expires_4}
#Enable or disable the 100 reliable retransmission; 0-Disabled (default), 1-Enabled;
account.4.100rel_enable = {$yealink_retransmission}
#Enable or disable the resource reservation; 0-Disabled (default), 1-Enabled;
account.4.precondition =
#Enable or disable the phone to subscribe the register status; 0-Disabled (default), 1-Enabled;
account.4.subscribe_register =
#Enable or disable the phone to subscribe the message waiting indicator; 0-Disabled (default), 1-Enabled;
account.4.subscribe_mwi =
#Configure MWI subscribe expiry time (in seconds). It ranges from 0 to 84600, the default value is 3600.
account.4.subscribe_mwi_expires =
#Configure the type of SIP header(s) to carry the caller ID; 0-FROM (default), 1-PAI 2-PAI-FROM, 3-PRID-PAI-FROM, 4-PAI-RPID-FROM, 5-RPID-FROM;
account.4.cid_source = {$yealink_cid_source}
#Configure the presentation of the callee ID; 0-PAI-PRID, 1-DIALED DIGITS (default), 2-RFC4916;
account.4.cp_source = 2
#Enable or disable the session timer; 0-Disabled (default), 1-Enabled;
account.4.session_timer.enable = {$yealink_session_timer}
#Configure the refresh session timer interval (in seconds). It ranges from 1 to 9999.
account.4.session_timer.expires =
#Configure the session timer refresher; 0-Uac (default), 1-Uas;
account.4.session_timer.refresher =
#Enable or disable the "user=phone"; 0-Disabled (default), 1-Enabled;
account.4.enable_user_equal_phone =
#Specify whether to encrypt the SIP messages; 0-Disabled, 1-Forced, 2-Negotiated;
account.4.srtp_encryption =
#Configure the RTP packet time. The valid values are 0 (Disabled), 10, 20 (default), 30, 40, 50, 60.
account.4.ptime =
#Assign account 4 as shared line; 0-Disabled (default), 1-BSFT shared line, 2-Draft bridge line appearance;
{if isset($shared_line_4) }
account.4.shared_line = {$shared_line_4}
{else}
account.4.shared_line = 0
{/if}
#Configure BLA number for account 4 and the subscribe period (in seconds). It ranges from 60 to 7200, the default value is 300.
account.4.bla_number =
account.4.bla_subscribe_period =
#Enable or disable call pickup using dialog-info SIP header; 0-Disabled (default), 1-Enabled;
account.4.dialoginfo_callpickup =
#Configure the directed and group pickup codes for account 4, the settings on a per-account basis take precedence over the settings on the phone.
account.4.group_pickup_code =
account.4.direct_pickup_code =
#Enable or disable the auto answer feature; 0-Disabled (default), 1-Enabled;
account.4.auto_answer =
#Enable or disable the phone to record the missed call; 0-Disabled, 1-Enabled (default);
account.4.missed_calllog =
#Enable or disable the phone to subscribe to the voicemail through the message waiting indicator; 0-Disabled (default), 1-Enabled;
account.4.subscribe_mwi_to_vm =
#Enable or disable the phone to send the MAC address in the Register message; 0-Disabled (default), 1-Enabled;
account.4.register_mac =
#Enable or disable the phone to send theline number in the Register message; 0-Disabled, 1-Enabled (default);
account.4.register_line =
#Configure the interval (in seconds) the phone retries to register when account 4 fails to register. It ranges from 0 to 1800, the default value is 30.
account.4.reg_fail_retry_interval =
#Configure the conference type; 0-Local (default), 2-Network Conference;
account.4.conf_type =
#Configure the conference URI (a SIP URI, or use part of the SIP URI). For example, "conference@domain.com" or "conference".
account.4.conf_uri =
#Configure the BLF list URI (a SIP URI, or use part of the SIP URI). For example, "2300_blflist@domain.com" or "2300_blflist".
account.4.blf.blf_list_uri =
#Configure the pickup code of BLF List.
account.4.blf_list_code =
#Configure the bargein code.
account.4.blf_list_barge_in_code =
#Configure the BLF subscribe period (in seconds), the default value is 1800.
account.4.blf.subscribe_period =
#Configure the ACD subscribe period (in seconds). It ranges from 120 to 3600 (default).
account.4.subscribe_acd_expires =
#Configure the SIP server type; 0-Default (default), 2-BroadSoft, 4-Cosmocom;
account.4.sip_server_type =
#Enable or disable the phone to use the customized theme; 0-Disabled (default), 1-Enabled;
account.4.idle_screen_enable =
#Define the access URL of the customized theme.
account.4.idle_screen_url =
#Enable or disable the SIP signal encode; 0-Disabled (default), 1-Enabled (RC 4);
account.4.enable_signal_encode =
#Configure the key for encoding.
account.4.signal_encode_key =
#Configure the DTMF type; 0-INBAND, 1-RFC2833 (default), 2-SIP INFO, 3-AUTO+SIP INFO;
account.4.dtmf.type =
#Configure the RFC2833 payload. It ranges from 96 to 225, the default value is 101.
account.4.dtmf.dtmf_payload =
#Configure the DTMF info type when using the SIP INFO; 0-Disabled (default), 1-DTMF-Relay, 2-DTMF, 3-Telephone-Event;
account.4.dtmf.info_type =
#Enable or disable the phone to support the simplified SIP header; 0-Disabled (default), 1-Enabled;
account.4.compact_header_enable =
#########################################################################
## NAT Settings ##
#########################################################################
#Enable or disable the NAT traversal; 0-Disabled (default), 1-STUN;
account.4.nat.nat_traversal = {if isset($stun_server)}1{else}0{/if}
#Configure the STUN server address.
account.4.nat.stun_server = {$stun_server}
#Configure the STUN server port, the default value is 3478.
account.4.nat.stun_port = {if isset($stun_port)}{$stun_port}{else}3478{/if}
#Enable or disable the NAT keep-alive; 0-Disabled, 1-Enabled (default);
account.4.nat.udp_update_enable =
#Specify the keep-alive interval (in seconds), the default value is 30.
account.4.nat.udp_update_time =
#Enable or disable the NAT Rport; 0-Disabled (default), 1-Enabled;
account.4.nat.rport = {$yealink_rport}
#Configure the session timer (in seconds), the default values of T1, T2, T3 are 0.5, 4, 5.
account.4.advanced.timer_t1 =
account.4.advanced.timer_t2 =
account.4.advanced.timer_t4 =
#Assign a ringtone for account 4. The system ring tones are: common.wav (default), Ring1.wav, Ring2.wav,¡­¡­Ring8.wav.
#If you configure the custom ring tone (Family.wav) for the account, the value format is: Family.wav
#If you configure the system ring tone (Ring2.wav) for the account, the value format is: Ring2.wav
account.4.ringtone.ring_type =
#Enable or disable the phone to download the picture when receiving the specified SIP message; 0-Disabled, 1-Enabled (default);
account.4.picture_info_enable =
#Enable or disable the phone to display the picture when receiving the specified SIP message; 0-Disabled, 1-Enabled (default);
account.4.picture_info_enable =
#Audio codecs for account 4 (Y ranges from 1 to 13).
#account.4.codec.Y.enable =
#account.4.codec.Y.payload_type =
#account.4.codec.Y.priority =
#account.4.codec.Y.rtpmap =
account.4.codec.1.enable = 1
account.4.codec.1.payload_type = PCMU
account.4.codec.1.priority = 1
account.4.codec.1.rtpmap = 0
account.4.codec.2.enable = 1
account.4.codec.2.payload_type = PCMA
account.4.codec.2.priority = 2
account.4.codec.2.rtpmap = 8
account.4.codec.3.enable = 0
account.4.codec.3.payload_type = G723_53
account.4.codec.3.priority =4
account.4.codec.3.rtpmap = 4
account.4.codec.4.enable = 0
account.4.codec.4.payload_type = G723_63
account.4.codec.4.priority = 0
account.4.codec.4.rtpmap = 4
account.4.codec.5.enable = 1
account.4.codec.5.payload_type = G729
account.4.codec.5.priority = 3
account.4.codec.5.rtpmap = 18
account.4.codec.6.enable = 1
account.4.codec.6.payload_type = G722
account.4.codec.6.priority = 4
account.4.codec.6.rtpmap = 9
account.4.codec.7.enable =
account.4.codec.7.payload_type =
account.4.codec.7.priority =
account.4.codec.7.rtpmap =
account.4.codec.8.enable = 0
account.4.codec.8.payload_type = G726-16
account.4.codec.8.priority = 0
account.4.codec.8.rtpmap = 112
account.4.codec.9.enable = 0
account.4.codec.9.payload_type = G726-24
account.4.codec.9.priority = 0
account.4.codec.9.rtpmap = 102
account.4.codec.10.enable = 0
account.4.codec.10.payload_type = G726-32
account.4.codec.10.priority = 0
account.4.codec.10.rtpmap = 2
account.4.codec.11.enable = 0
account.4.codec.11.payload_type = G726-40
account.4.codec.11.priority = 0
account.4.codec.11.rtpmap = 104
account.4.codec.12.enable = 0
account.4.codec.12.payload_type = iLBC_13_3
account.4.codec.12.priority = 0
account.4.codec.12.rtpmap = 97
account.4.codec.13.enable = 0
account.4.codec.13.payload_type = iLBC_15_2
account.4.codec.13.priority = 0
account.4.codec.13.rtpmap = 97
#######################################################################################
## Account5 Settings (For T38G only) ##
#######################################################################################
#Enable or disable the account 5; 0-Disabled (default), 1-Enabled;
{if isset($user_password_5) }
account.5.enable = 1
{else}
account.5.enable = 0
{/if}
#Configure the label displayed on the LCD screen for account 5.
account.5.label = {$display_name_5}
#Configure the display name of account 5.
account.5.display_name = {$display_name_5}
#Configure the username and password for register authentication.
account.5.auth_name = {$auth_id_5}
account.5.password = {$user_password_5}
#Configure the register user name.
account.5.user_name = {$user_id_5}
#Enable or disable the phone to receive the messages from the server only; 0-Disabled (default), 1-Enabled;
account.5.sip_trust_ctrl = 1
#Configure the SIP server address.
account.5.sip_server_host = {$server_address_5}
#Specify the port for the SIP server. The default value is 5060.
account.5.sip_server_port = {$sip_port_5}
#Enable or disable the use of the outbound proxy server; 0-Disabled (default), 1-Enabled;
#Specify the IP address or domain name of the outbound proxy server.
account.5.outbound_host = {$outbound_proxy_5}
#Specify the server port, the default value is 5060.
account.5.outbound_port =
#Configure the transport type; 0-UDP (default), 1-TCP, 2-TLS, 3-DNS SRV;
{if $sip_transport_5 == 'udp'}account.5.transport = 0{/if}
{if $sip_transport_5 == 'tcp'}account.5.transport = 1{/if}
{if $sip_transport_5 == 'tls'}account.5.transport = 2{/if}
{if $sip_transport_5 == 'dns srv'}account.5.transport = 3{/if}
account.5.outbound_proxy.1.address = {$outbound_proxy_primary_5}
account.5.outbound_proxy.2.address = {$outbound_proxy_secondary_5}
account.5.outbound_proxy_enable = {if isset($outbound_proxy_primary_5)}1{else}0{/if}
#Configure the address of the backup outbound proxy server.
account.5.backup_outbound_host =
#Specify the port, the default value is 5060.
account.5.backup_outbound_port =
#Configure the voice mail number of account 5.
voice_mail.number.5 =
#Configure the proxy server to account 5.
account.5.proxy_require =
#Enable or disable the use of the timer to periodically refresh the DNS-SRV query result; 0-Disabled (default), 1-Enabled;
#Require reboot;
account.5.srv_ttl_timer_enable =
#Configure the type of DNS-SRV query; 0-UDP, TCP and TLS (default), 1-UDP, 2-TCP, 3-TLS;
#Require reboot;
account.5.dns_srv_type =
#Enable or disable the anonymous call feature; 0-Disabled (default), 1-Enabled;
account.5.anonymous_call =
#Configure the on code and off code of the anonymous call feature.
account.5.anonymous_call_oncode =
account.5.anonymous_call_offcode =
#Enable or disable the reject anonymous call feature; 0-Disabled (default), 1-Enabled;
account.5.reject_anonymous_call =
#Configure the on code and off code of the reject anonymous call feature.
account.5.anonymous_reject_oncode =
account.5.anonymous_reject_offcode =
#Configure the SIP port for account 5, the default value is 5060.
account.5.sip_listen_port =
#Configure the register expiry time (in seconds), the default value is 3600.
account.5.expires = {$register_expires_5}
#Enable or disable the 100 reliable retransmission; 0-Disabled (default), 1-Enabled;
account.5.100rel_enable = {$yealink_retransmission}
#Enable or disable the resource reservation; 0-Disabled (default), 1-Enabled;
account.5.precondition =
#Enable or disable the phone to subscribe the register status; 0-Disabled (default), 1-Enabled;
account.5.subscribe_register =
#Enable or disable the phone to subscribe the message waiting indicator; 0-Disabled (default), 1-Enabled;
account.5.subscribe_mwi =
#Configure MWI subscribe expiry time (in seconds). It ranges from 0 to 84600, the default value is 3600.
account.5.subscribe_mwi_expires =
#Configure the type of SIP header(s) to carry the caller ID; 0-FROM (default), 1-PAI 2-PAI-FROM, 3-PRID-PAI-FROM, 4-PAI-RPID-FROM, 5-RPID-FROM;
account.5.cid_source = {$yealink_cid_source}
#Configure the presentation of the callee ID; 0-PAI-PRID, 1-DIALED DIGITS (default), 2-RFC4916;
account.5.cp_source = 2
#Enable or disable the session timer; 0-Disabled (default), 1-Enabled;
account.5.session_timer.enable = {$yealink_session_timer}
#Configure the refresh session timer interval (in seconds). It ranges from 1 to 9999.
account.5.session_timer.expires =
#Configure the session timer refresher; 0-Uac (default), 1-Uas;
account.5.session_timer.refresher =
#Enable or disable the "user=phone"; 0-Disabled (default), 1-Enabled;
account.5.enable_user_equal_phone =
#Specify whether to encrypt the SIP messages; 0-Disabled, 1-Forced, 2-Negotiated;
account.5.srtp_encryption =
#Configure the RTP packet time. The valid values are 0 (Disabled), 10, 20 (default), 30, 40, 50, 60.
account.5.ptime =
#Assign account 5 as shared line; 0-Disabled (default), 1-BSFT shared line, 2-Draft bridge line appearance;
{if isset($shared_line_5) }
account.5.shared_line = {$shared_line_5}
{else}
account.5.shared_line = 0
{/if}
#Configure BLA number for account 5 and the subscribe period (in seconds). It ranges from 60 to 7200, the default value is 300.
account.5.bla_number =
account.5.bla_subscribe_period =
#Enable or disable call pickup using dialog-info SIP header; 0-Disabled (default), 1-Enabled;
account.5.dialoginfo_callpickup =
#Configure the directed and group pickup codes for account 5, the settings on a per-account basis take precedence over the settings on the phone.
account.5.group_pickup_code =
account.5.direct_pickup_code =
#Enable or disable the auto answer feature; 0-Disabled (default), 1-Enabled;
account.5.auto_answer =
#Enable or disable the phone to record the missed call; 0-Disabled, 1-Enabled (default);
account.5.missed_calllog =
#Enable or disable the phone to subscribe to the voicemail through the message waiting indicator; 0-Disabled (default), 1-Enabled;
account.5.subscribe_mwi_to_vm =
#Enable or disable the phone to send the MAC address and line number in the Register message; 0-Disabled (default), 1-Enabled;
account.5.register_mac =
account.5.register_line =
#Configure the interval (in seconds) the phone retries to register when account 5 fails to register. It ranges from 0 to 1800, the default value is 30.
account.5.reg_fail_retry_interval =
#Configure the conference type; 0-Local (default), 2-Network Conference;
account.5.conf_type =
#Configure the conference URI (a SIP URI, or use part of the SIP URI). For example, "conference@domain.com" or "conference".
account.5.conf_uri =
#Configure the BLF list URI (a SIP URI, or use part of the SIP URI). For example, "2300_blflist@domain.com" or "2300_blflist".
account.5.blf.blf_list_uri =
#Configure the pickup code of BLF List.
account.5.blf_list_code =
#Configure the bargein code.
account.5.blf_list_barge_in_code =
#Configure the BLF subscribe period (in seconds), the default value is 1800.
account.5.blf.subscribe_period =
#Configure the ACD subscribe period (in seconds). It ranges from 120 to 3600 (default).
account.5.subscribe_acd_expires =
#Configure the SIP server type; 0-Default (default), 2-BroadSoft, 4-Cosmocom;
account.5.sip_server_type =
#Enable or disable the phone to use the customized theme; 0-Disabled (default), 1-Enabled;
account.5.idle_screen_enable =
#Define the access URL of the customized theme.
account.5.idle_screen_url =
#Enable or disable the SIP signal encode; 0-Disabled (default), 1-Enabled (RC 4);
account.5.enable_signal_encode =
#Configure the key for encoding.
account.5.signal_encode_key =
#Configure the DTMF type; 0-INBAND, 1-RFC2833 (default), 2-SIP INFO, 3-AUTO+SIP INFO;
account.5.dtmf.type =
#Configure the RFC2833 payload. It ranges from 96 to 225, the default value is 101.
account.5.dtmf.dtmf_payload =
#Configure the DTMF info type when using the SIP INFO; 0-Disabled (default), 1-DTMF-Relay, 2-DTMF, 3-Telephone-Event;
account.5.dtmf.info_type =
#Enable or disable the phone to support the simplified SIP header; 0-Disabled (default), 1-Enabled;
account.5.compact_header_enable =
#########################################################################
## NAT Settings ##
#########################################################################
#Enable or disable the NAT traversal; 0-Disabled (default), 1-STUN;
account.5.nat.nat_traversal = {if isset($stun_server)}1{else}0{/if}
#Configure the STUN server address.
account.5.nat.stun_server = {$stun_server}
#Configure the STUN server port, the default value is 3478.
account.5.nat.stun_port = {if isset($stun_port)}{$stun_port}{else}3478{/if}
#Enable or disable the NAT keep-alive; 0-Disabled, 1-Enabled (default);
account.5.nat.udp_update_enable =
#Specify the keep-alive interval (in seconds), the default value is 30.
account.5.nat.udp_update_time =
#Enable or disable the NAT Rport; 0-Disabled (default), 1-Enabled;
account.5.nat.rport = {$yealink_rport}
#Configure the session timer (in seconds), the default value of T1, T2, T3 is 0.5, 4, 5.
account.5.advanced.timer_t1 =
account.5.advanced.timer_t2 =
account.5.advanced.timer_t4 =
#Assign a ringtone for account 5. The system ring tones are: common.wav (default), Ring1.wav, Ring2.wav,¡­¡­Ring8.wav.
#If you configure the custom ring tone (Family.wav) for the account, the value format is: Family.wav
#If you configure the system ring tone (Ring2.wav) for the account, the value format is: Ring2.wav
account.5.ringtone.ring_type =
#Enable or disable the phone to display the picture when receiving the specified SIP message; 0-Disabled, 1-Enabled (default);
account.5.picture_info_enable =
#Audio codecs for account5 (Y ranges from 1 to 13).
#account.5.codec.Y.enable =
#account.5.codec.Y.payload_type =
#account.5.codec.Y.priority =
#account.5.codec.Y.rtpmap =
account.5.codec.1.enable = 1
account.5.codec.1.payload_type = PCMU
account.5.codec.1.priority = 1
account.5.codec.1.rtpmap = 0
account.5.codec.2.enable = 1
account.5.codec.2.payload_type = PCMA
account.5.codec.2.priority = 2
account.5.codec.2.rtpmap = 8
account.5.codec.3.enable = 0
account.5.codec.3.payload_type = G723_53
account.5.codec.3.priority =4
account.5.codec.3.rtpmap = 4
account.5.codec.4.enable = 0
account.5.codec.4.payload_type = G723_63
account.5.codec.4.priority = 0
account.5.codec.4.rtpmap = 4
account.5.codec.5.enable = 1
account.5.codec.5.payload_type = G729
account.5.codec.5.priority = 3
account.5.codec.5.rtpmap = 18
account.5.codec.6.enable = 1
account.5.codec.6.payload_type = G722
account.5.codec.6.priority = 4
account.5.codec.6.rtpmap = 9
account.5.codec.7.enable =
account.5.codec.7.payload_type =
account.5.codec.7.priority =
account.5.codec.7.rtpmap =
account.5.codec.8.enable = 0
account.5.codec.8.payload_type = G726-16
account.5.codec.8.priority = 0
account.5.codec.8.rtpmap = 112
account.5.codec.9.enable = 0
account.5.codec.9.payload_type = G726-24
account.5.codec.9.priority = 0
account.5.codec.9.rtpmap = 102
account.5.codec.10.enable = 0
account.5.codec.10.payload_type = G726-32
account.5.codec.10.priority = 0
account.5.codec.10.rtpmap = 2
account.5.codec.11.enable = 0
account.5.codec.11.payload_type = G726-40
account.5.codec.11.priority = 0
account.5.codec.11.rtpmap = 104
account.5.codec.12.enable = 0
account.5.codec.12.payload_type = iLBC_13_3
account.5.codec.12.priority = 0
account.5.codec.12.rtpmap = 97
account.5.codec.13.enable = 0
account.5.codec.13.payload_type = iLBC_15_2
account.5.codec.13.priority = 0
account.5.codec.13.rtpmap = 97
#######################################################################################
## Account6 Settings (For T38G only) ##
#######################################################################################
#Enable or disable the account 6; 0-Disabled (default), 1-Enabled;
{if isset($user_password_6) }
account.6.enable = 1
{else}
account.6.enable = 0
{/if}
#Configure the label displayed on the LCD screen for account 6.
account.6.label = {$display_name_6}
#Configure the display name of account 6.
account.6.display_name = {$display_name_6}
#Configure the username and password for register authentication.
account.6.auth_name = {$auth_id_6}
account.6.password = {$user_id_6}
#Configure the register user name.
account.6.user_name = {$user_id_6}
#Enable or disable the phone to receive the messages from the server only; 0-Disabled (default), 1-Enabled;
account.6.sip_trust_ctrl = 1
#Configure the SIP server address.
account.6.sip_server_host = {$server_address_6}
#Specify the port for the SIP server. The default value is 5060.
account.6.sip_server_port = {$sip_port_6}
#Enable or disable the use of the outbound proxy server; 0-Disabled (default), 1-Enabled;
#Specify the IP address or domain name of the outbound proxy server.
account.6.outbound_host = {$outbound_proxy_6}
#Specify the server port, the default value is 5060.
account.6.outbound_port =
#Configure the transport type; 0-UDP (default), 1-TCP, 2-TLS, 3-DNS SRV;
{if $sip_transport_6 == 'udp'}account.6.transport = 0{/if}
{if $sip_transport_6 == 'tcp'}account.6.transport = 1{/if}
{if $sip_transport_6 == 'tls'}account.6.transport = 2{/if}
{if $sip_transport_6 == 'dns srv'}account.6.transport = 3{/if}
account.6.outbound_proxy.1.address = {$outbound_proxy_primary_6}
account.6.outbound_proxy.2.address = {$outbound_proxy_secondary_6}
account.6.outbound_proxy_enable = {if isset($outbound_proxy_primary_6)}1{else}0{/if}
#Configure the address of the backup outbound proxy server.
account.6.backup_outbound_host =
#Specify the port, the default value is 5060.
account.6.backup_outbound_port =
#Configure the voice mail number of account 6.
voice_mail.number.6 =
#Configure the proxy server to account 6.
account.6.proxy_require =
#Enable or disable the use of the timer to periodically refresh the DNS-SRV query result; 0-Disabled (default), 1-Enabled;
#Require reboot;
account.6.srv_ttl_timer_enable =
#Configure the type of DNS-SRV query; 0-UDP, TCP and TLS (default), 1-UDP, 2-TCP, 3-TLS;
#Require reboot;
account.6.dns_srv_type =
#Enable or disable the anonymous call feature; 0-Disabled (default), 1-Enabled;
account.6.anonymous_call =
#Configure the on code and off code of the anonymous call feature.
account.6.anonymous_call_oncode =
account.6.anonymous_call_offcode =
#Enable or disable the reject anonymous call feature; 0-Disabled (default), 1-Enabled;
account.6.reject_anonymous_call =
#Configure the on code and off code of the reject anonymous call feature.
account.6.anonymous_reject_oncode =
account.6.anonymous_reject_offcode =
#Configure the SIP port for account 6, the default value is 5060.
account.6.sip_listen_port =
#Configure the register expiry time (in seconds), the default value is 3600.
account.6.expires = {$register_expires_6}
#Enable or disable the 100 reliable retransmission; 0-Disabled (default), 1-Enabled;
account.6.100rel_enable = {$yealink_retransmission}
#Enable or disable the resource reservation; 0-Disabled (default), 1-Enabled;
account.6.precondition =
#Enable or disable the phone to subscribe the register status; 0-Disabled (default), 1-Enabled;
account.6.subscribe_register =
#Enable or disable the phone to subscribe the message waiting indicator; 0-Disabled (default), 1-Enabled;
account.6.subscribe_mwi = 0
#Configure MWI subscribe expiry time (in seconds). It ranges from 0 to 84600, the default value is 3600.
account.6.subscribe_mwi_expires = 3600
#Configure the type of SIP header(s) to carry the caller ID; 0-FROM (default), 1-PAI 2-PAI-FROM, 3-PRID-PAI-FROM, 4-PAI-RPID-FROM, 5-RPID-FROM;
account.6.cid_source = {$yealink_cid_source}
#Configure the presentation of the callee ID; 0-PAI-PRID, 1-DIALED DIGITS (default), 2-RFC4916;
account.6.cp_source = 2
#Enable or disable the session timer; 0-Disabled (default), 1-Enabled;
account.6.session_timer.enable = {$yealink_session_timer}
#Configure the refresh session timer interval (in seconds). It ranges from 1 to 9999.
account.6.session_timer.expires =
#Configure the session timer refresher; 0-Uac (default), 1-Uas;
account.6.session_timer.refresher =
#Enable or disable the "user=phone"; 0-Disabled (default), 1-Enabled;
account.6.enable_user_equal_phone =
#Specify whether to encrypt the SIP messages; 0-Disabled, 1-Forced, 2-Negotiated;
account.6.srtp_encryption =
#Configure the RTP packet time. The valid values are 0 (Disabled), 10, 20 (default), 30, 40, 50, 60.
account.6.ptime =
#Assign account 6 as shared line; 0-Disabled (default), 1-BSFT shared line, 2-Draft bridge line appearance;
{if isset($shared_line_6) }
account.6.shared_line = {$shared_line_6}
{else}
account.6.shared_line = 0
{/if}
#Configure BLA number for account 6 and the subscribe period (in seconds). It ranges from 60 to 7200, the default value is 300.
account.6.bla_number =
account.6.bla_subscribe_period =
#Enable or disable call pickup using dialog-info SIP header; 0-Disabled (default), 1-Enabled;
account.6.dialoginfo_callpickup =
#Configure the directed and group pickup codes for account 6, the settings on a per-account basis take precedence over the settings on the phone.
account.6.group_pickup_code =
account.6.direct_pickup_code =
#Enable or disable the auto answer feature; 0-Disabled (default), 1-Enabled;
account.6.auto_answer =
#Enable or disable the phone to record the missed call; 0-Disabled, 1-Enabled (default);
account.6.missed_calllog =
#Enable or disable the phone to subscribe to the voicemail through the message waiting indicator; 0-Disabled (default), 1-Enabled;
account.6.subscribe_mwi_to_vm = 0
#Enable or disable the phone to send the MAC address and line number in the Register message; 0-Disabled (default), 1-Enabled;
account.6.register_mac =
account.6.register_line =
#Configure the interval (in seconds) the phone retries to register when account 6 fails to register. It ranges from 0 to 1800, the default value is 30.
account.6.reg_fail_retry_interval =
#Configure the conference type; 0-Local (default), 2-Network Conference;
account.6.conf_type =
#Configure the conference URI (a SIP URI, or use part of the SIP URI). For example, "conference@domain.com" or "conference".
account.6.conf_uri =
#Configure the BLF list URI (a SIP URI, or use part of the SIP URI). For example, "2300_blflist@domain.com" or "2300_blflist".
account.6.blf.blf_list_uri =
#Configure the pickup code of BLF List.
account.6.blf_list_code =
#Configure the bargein code.
account.6.blf_list_barge_in_code =
#Configure the BLF subscribe period (in seconds), the default value is 1800.
account.6.blf.subscribe_period =
#Configure the ACD subscribe period (in seconds). It ranges from 120 to 3600 (default).
account.6.subscribe_acd_expires =
#Configure the SIP server type; 0-Default (default), 2-BroadSoft, 4-Cosmocom;
account.6.sip_server_type =
#Enable or disable the phone to use the customized theme; 0-Disabled (default), 1-Enabled;
account.6.idle_screen_enable =
#Define the access URL of the customized theme.
account.6.idle_screen_url =
#Enable or disable the SIP signal encode; 0-Disabled (default), 1-Enabled (RC 4);
account.6.enable_signal_encode =
#Configure the key for encoding.
account.6.signal_encode_key =
#Configure the DTMF type; 0-INBAND, 1-RFC2833 (default), 2-SIP INFO, 3-AUTO+SIP INFO;
account.6.dtmf.type =
#Configure the RFC2833 payload. It ranges from 96 to 225, the default value is 101.
account.6.dtmf.dtmf_payload =
#Configure the DTMF info type when using the SIP INFO; 0-Disabled (default), 1-DTMF-Relay, 2-DTMF, 3-Telephone-Event;
account.6.dtmf.info_type =
#Enable or disable the phone to support the simplified SIP header; 0-Disabled (default), 1-Enabled;
account.6.compact_header_enable =
#########################################################################
## NAT Settings ##
#########################################################################
#Enable or disable the NAT traversal; 0-Disabled (default), 1-STUN;
account.6.nat.nat_traversal =
#Configure the STUN server address.
account.6.nat.stun_server =
#Configure the STUN server port, the default value is 3478.
account.6.nat.stun_port =
#Enable or disable the NAT keep-alive; 0-Disabled, 1-Enabled (default);
account.6.nat.udp_update_enable =
#Specify the keep-alive interval (in seconds), the default value is 30.
account.6.nat.udp_update_time =
#Enable or disable the NAT Rport; 0-Disabled (default), 1-Enabled;
account.6.nat.rport = {$yealink_rport}
#Configure the session timer (in seconds), the default value of T1, T2, T3 is 0.5, 4, 5.
account.6.advanced.timer_t1 =
account.6.advanced.timer_t2 =
account.6.advanced.timer_t4 =
#Assign a ringtone for account 6. The system ring tones are: common.wav (default), Ring1.wav, Ring2.wav,¡­¡­Ring8.wav.
#If you configure the custom ring tone (Family.wav) for the account, the value format is: Family.wav
#If you configure the system ring tone (Ring2.wav) for the account, the value format is: Ring2.wav
account.6.ringtone.ring_type =
#Enable or disable the phone to display the picture when receiving the specified SIP message; 0-Disabled, 1-Enabled (default);
account.6.picture_info_enable =
#Audio codecs for account6 (Y ranges from 1 to 13).
#account.6.codec.Y.enable =
#account.6.codec.Y.payload_type =
#account.6.codec.Y.priority =
#account.6.codec.Y.rtpmap =
account.6.codec.1.enable = 1
account.6.codec.1.payload_type = PCMU
account.6.codec.1.priority = 1
account.6.codec.1.rtpmap = 0
account.6.codec.2.enable = 1
account.6.codec.2.payload_type = PCMA
account.6.codec.2.priority = 2
account.6.codec.2.rtpmap = 8
account.6.codec.3.enable = 0
account.6.codec.3.payload_type = G723_53
account.6.codec.3.priority =4
account.6.codec.3.rtpmap = 4
account.6.codec.4.enable = 0
account.6.codec.4.payload_type = G723_63
account.6.codec.4.priority = 0
account.6.codec.4.rtpmap = 4
account.6.codec.5.enable = 1
account.6.codec.5.payload_type = G729
account.6.codec.5.priority = 3
account.6.codec.5.rtpmap = 18
account.6.codec.6.enable = 1
account.6.codec.6.payload_type = G722
account.6.codec.6.priority = 4
account.6.codec.6.rtpmap = 9
account.6.codec.7.enable =
account.6.codec.7.payload_type =
account.6.codec.7.priority =
account.6.codec.7.rtpmap =
account.6.codec.8.enable = 0
account.6.codec.8.payload_type = G726-16
account.6.codec.8.priority = 0
account.6.codec.8.rtpmap = 112
account.6.codec.9.enable = 0
account.6.codec.9.payload_type = G726-24
account.6.codec.9.priority = 0
account.6.codec.9.rtpmap = 102
account.6.codec.10.enable = 0
account.6.codec.10.payload_type = G726-32
account.6.codec.10.priority = 0
account.6.codec.10.rtpmap = 2
account.6.codec.11.enable = 0
account.6.codec.11.payload_type = G726-40
account.6.codec.11.priority = 0
account.6.codec.11.rtpmap = 104
account.6.codec.12.enable = 0
account.6.codec.12.payload_type = iLBC_13_3
account.6.codec.12.priority = 0
account.6.codec.12.rtpmap = 97
account.6.codec.13.enable = 0
account.6.codec.13.payload_type = iLBC_15_2
account.6.codec.13.priority = 0
account.6.codec.13.rtpmap = 97
#######################################################################################
## Call Forward ##
#######################################################################################
#Enable or disable the always forward; 0-Disabled (default), 1-Enabled;
forward.always.enable =
#Configure the target number that the phone will forward the call to.
forward.always.target =
#Configure the on code and off code to always forward.
forward.always.on_code =
forward.always.off_code =
#Enable or disable the busy forward; 0-Disabled (default), 1-Enabled;
forward.busy.enable =
forward.busy.target =
forward.busy.on_code =
forward.busy.off_code =
#Enable or disable the no answer forward; 0-Disabled (default), 1-Enabled;
#Configure the waiting ring times before forwarding. It ranges from 0 to 20, the default value is 10.
forward.no_answer.enable =
forward.no_answer.target =
forward.no_answer.timeout =
forward.no_answer.on_code =
forward.no_answer.off_code =
#Enable or disable the phone to forward the call to the international number (the prefix is 00); 0-Disabled (default), 1-Enabled;
forward.international.enable =
#######################################################################################
## Line Key ##
#######################################################################################
#The x of the parameter "linekey.x.line" ranges from 1 to 6.
#The default value equals to the value of x. For example, the default value of the parameter "linekey.1.line" is 1.
#linekey.x.lable--Define the label for each line key.
{foreach $keys['line'] as $row}
#Configure Line Key {$row.device_key_id}
linekey.{$row.device_key_id}.line = {$row.device_key_line}
linekey.{$row.device_key_id}.value = {$row.device_key_value}
linekey.{$row.device_key_id}.pickup_value = {$row.device_key_extension}
linekey.{$row.device_key_id}.type = {$row.device_key_type}
linekey.{$row.device_key_id}.xml_phonebook =
linekey.{$row.device_key_id}.label = {$row.device_key_label}
{/foreach}
#######################################################################################
## Memory Key (For T38G only) ##
#######################################################################################
#X ranges from 1 to 10;
#memorykey.x.line--Configure the desired line to apply the key feature. It ranges from 0 to 6.
#The value 0 of the "memorykey.x.line" stands for Auto, it means the first available line.
#But, when the DSS key is configured as BLF, BLF List, Shared Line, Call Park, Pick Up, ACD or Voice Mail feature, the value 0 stands for line 1.
#memorykey.x.value--Enter the value of some features. E.g. When configuring the DSS key to be BLF, enter the number of the monitored user.
#memorykey.x.pickup_value--Enter the pickup code, this parameter is only appilicable to BLF.
#memorykey.x.type--Assign the desired feature to the memory key.
#Valid types are: 0-N/A(default for memory key) 1-Conference 2-Forward 3-Transfer 4-Hold 5-DND 6-Redial 7-Call Return 8-SMS
# 9-Call Pickup 10-Call Park 11-DTMF 12-Voicemail 13-SpeedDial 14-Intercom 15-Line(default for line key) 16-BLF 17-URL
# 18-Group Listening 19-Public Hold 20-Private 21-Shared Line 22-XML Group 23-Group Pickup 24-Paging 25-Record 27-XML Browser
# 34-Hot Desking 35-URL Record 38-LDAP 39-BLF List 40-Prefix 41-Zero-Sp-Touch 42-ACD 45-Local Group 46-Broadsoft Group
#memorykey.x.xml_phonebook--Specify the desired remote phonebook/local group/BSFT phonebook for the DSS key. This parameter is only appilicable to the feature XML Group/Local Group/Broadsoft Group.
#memorykey.x.sub_type =
{foreach $keys["memory"] as $row}
#Expansion Memory Key {$row.device_key_id}
memorykey.{$row.device_key_id}.type = {$row.device_key_type}
memorykey.{$row.device_key_id}.line = {$row.device_key_line}
memorykey.{$row.device_key_id}.value = {$row.device_key_value}
memorykey.{$row.device_key_id}.pickup_value = {$row.device_key_extension}
memorykey.{$row.device_key_id}.label = {$row.device_key_label}
memorykey.{$row.device_key_id}.xml_phonebook =
memorykey.{$row.device_key_id}.sub_type =
{/foreach}
##########################################################################################
## Programmable Key (For T38G only) ##
##########################################################################################
#X ranges from 1 to 15.
#programablekey.x.type--Customize the programmable key type.
#The valid types are:
#0-N/A 2-Forward 5-DND 6-Redial 7-Call Return 8-SMS 9-Call Pickup 13-Spead Dial 14-Intercom
#22-XML Group 23-Group Pickup 27-XML Browser 28-History 29-Directory 30-Menu 32-New SMS 33-Status 43-Local Phonebook
#44-Broadsoft Phonebook 45-Local Group 46-Broadsoft Group 47-XML Phonebook 48-Switch Account Up 49-Switch Account Down 50-Keypad Lock
#programablekey.x.line--Configure the desired line to apply the key feature. It ranges from 0 to 6.
#The value 0 of the "proramablekey.x.line" stands for Auto, it means the first available line.
#But, when the programmable key is configured as Pick Up, the value 0 stands for line 1.
{foreach $keys["programmable"] as $row}
programablekey.{$row.device_key_id}.type = {$row.device_key_type}
programablekey.{$row.device_key_id}.line = {$row.device_key_line}
programablekey.{$row.device_key_id}.value = {$row.device_key_value}
programablekey.{$row.device_key_id}.xml_phonebook =
programablekey.{$row.device_key_id}.history_type =
programablekey.{$row.device_key_id}.label = {$row.device_key_label}
{/foreach}
#programablekey.x.value =
#programablekey.x.xml_phonebook--Specify the desired remote phonebook/local group/BSFT phonebook for the programmable key. This parameter is only appilicable to the feature XML Group/Local Group/Broadsoft Group.
#programablekey.x.history_type =
#programablekey.x.label--This parameter is only available to the key 1 to key 4.
#History
#programablekey.1.type = 28
#programablekey.1.line = 1
#programablekey.1.value =
#programablekey.1.xml_phonebook =
#programablekey.1.history_type =
#programablekey.1.label =
#Directory
#programablekey.2.type = 29
#programablekey.2.line = 1
#programablekey.2.value =
#programablekey.2.xml_phonebook =
#programablekey.2.history_type =
#programablekey.2.label =
#DND
programablekey.3.type = 5
programablekey.3.line = 1
programablekey.3.value =
programablekey.3.xml_phonebook =
programablekey.3.history_type =
programablekey.3.label =
#Menu
#programablekey.4.type = 30
#programablekey.4.line =
#programablekey.4.value =
#programablekey.4.xml_phonebook =
#programablekey.4.history_type =
#programablekey.4.label =
##########################################################################################
## Expansion Module 1 ##
##########################################################################################
#X ranges from 1 to 16, Y ranges from 1 to 40.
#expansion_module.x.key.y.type = 37 (Switch by default)
#expansion_module.x.key.y.line = 0
#expansion_module.x.key.y.value =
#expansion_module.x.key.y.pickup_value =
#expansion_module.x.key.y.label =
#expansion_module.X.key.Y.xml_phonebook =
{$rownum = 1}
{foreach $keys["expansion"] as $row}
{if $rownum <= 40}
expansion_module.1.key.{$row.device_key_id}.type = {$row.device_key_type}
expansion_module.1.key.{$row.device_key_id}.line = {$row.device_key_line}
expansion_module.1.key.{$row.device_key_id}.value = {$row.device_key_value}
expansion_module.1.key.{$row.device_key_id}.pickup_value = {$row.device_key_extension}
expansion_module.1.key.{$row.device_key_id}.label = {$row.device_key_label}
expansion_module.1.key.{$row.device_key_id}.xml_phonebook =
{else}
expansion_module.2.key.{$row.device_key_id - 40}.type = {$row.device_key_type}
expansion_module.2.key.{$row.device_key_id - 40}.line = {$row.device_key_line}
expansion_module.2.key.{$row.device_key_id - 40}.value = {$row.device_key_value}
expansion_module.2.key.{$row.device_key_id - 40}.extension = {$row.device_key_extension}
expansion_module.2.key.{$row.device_key_id - 40}.label = {$row.device_key_label}
expansion_module.2.key.{$row.device_key_id - 40}.xml_phonebook =
{/if}
{$rownum = $rownum + 1}
{/foreach}
##########################################################################################
## Expansion Module 2 ##
##########################################################################################
#Expansion module 2 key 1
#expansion_module.2.key.1.type = {$key_type_1}
#expansion_module.2.key.1.line = {$key_id_1}
#expansion_module.2.key.1.value = {$key_value_1}
#expansion_module.2.key.1.pickup_value =
#expansion_module.2.key.1.label = {$key_label_1}
#expansion_module.2.key.1.xml_phonebook =
#expansion_module.2.key.1.type = 37
#expansion_module.2.key.1.label = {$key_label_1}
Reference in New Issue View Git Blame Copy Permalink